REFRIGERATOR NOT COOLING ENOUGH
If the refrigerator is running, but not cooling at all or is not cold enough, several factors may influence the temperature. Check the following:
Check the temperature control settings:
For Dial or Digital Readout Models, adjust your temperature control by one number higher for a cooler temperature setting.
Adjusting the temperature on set point models:
Adjusting the temperature on knob models:
Adjusting the temperature on single temperature models:
Adjusting the temperature on dual control models:
For Actual Temperature Readout Models, adjust your temperature control by one degree lower for a lower temperature setting.
Adjusting the temperature on actual temp models:
If this is a new unit:
Allow about 24 hours for the unit to cool down and stabilize after initial installation. If 24 has passed and the controls have been set properly but the unit is still warm, you may need to schedule service. Schedule a service appointment online.
Make sure that both the refrigerator and freezer contain a reasonable food load.
Closed containers of water, food or non-perishables will help to stabilize the temperature. This is because the items in the refrigerator absorb the cold, and actually work to help the refrigerator maintain a steady temperature, in much the same way that ice cubes keep a drink cold. When you open the refrigerator door, the cool air rushes out and warm air rushes in. The more items in the refrigerator, the less cool air is needed to keep the refrigerator cold. Therefore, when you close the door again, the refrigerator returns to a stable temperature more quickly.
Make sure refrigerator and freezer doors can close and can properly seal.
Check for large items, such as trays, platters, food items (like pizza boxes), and ice behind the ice bin that may interfere with door closure.
If the doors do not close on their own when partially opened, you may need to adjust the leveling legs or rollers so that the front is higher than the back. Keep adjusting the level until the door closes on its own when you open the door halfway (45 degree angle).
Make sure door gaskets are sealing properly.
Adjust your door gasket:
Check to see if large containers are placed against the back wall of the refrigerator.
The large containers in back may block the flow of cold air and adversely affect the temperatures in the refrigerator. Move the tall items so they don’t block the air flow.
Check to see if the condenser is dirty.
To minimize the possibility of electric shock, unplug the appliance before attempting any maintenance or cleaning.
When the condenser coils get dirty the sealed system does not operate as efficiently. See Cleaning Condenser Coils on Refrigerator
Some refrigerators (2001 and newer) have condenser coils in a location that does not require them to be cleaned. If your model has coils that need to be cleaned, directions will be in your owner’s manual. Download a copy of the Owner’s Manual.
2001 and newer compact refrigerators and smaller capacity top freezers still have coils to be cleaned.
If the owner’s manual indicates the model has coils to be cleaned, follow the directions in the manual.
Be sure the refrigerator is installed in an area where the temperature will not go below 60°F (16°C) or exceed 110°F.
Your refrigerator may not cool normally if installed outside of these temperature ranges.
Verify that the refrigerator has proper air clearance.
In general, at least 1 inch of clearance is required on each side, top and back of the refrigerator. Clearance requirements may vary model to model. Please consult your owner’s user manual for specific requirements. Download a copy of the Owner’s Manual and/or Installation Instructions.
Make sure the interior lights are going off when the doors are closed.
To check on most models, close the door slowly. The light should go out when the door opening is reduced to approximately 1 inch. If the light stays on, it may produce heat that affects your refrigerator temperature.
If the refrigerator door is misaligned, the light will stay on. If the light stays on, your refrigerator will not cool properly.
If the refrigerator has just been serviced, it could still be in a diagnostic mode.
Disconnect power to your refrigerator for 30 seconds and this should clear the control panel. The refrigerator should now cool normally.
For more information on GTS18F and GTS21F Top Freezer refrigerators, please view the following video:
If the above items do not fix the issue and you still have a no cool situation, you may need to schedule service. For service, please schedule a service appointment with GE Appliances Factory Service.
MAKE SURE YOU LEAVE THE UNIT PLUGGED IN UNTIL THE TECHNICIAN ARRIVES. This is to ensure that the symptoms will not disappear.
For quick and reliable appliance repairs call Appliance Masters or Book an appointment online
Simple and Hassle-Free Repair
At Appliance Masters, we understand the inconvenience of having to deal with a broken down appliance, and that’s why we strive to provide as simple and as hassle-free a service as possible. Our technicians travel in vehicles that carry 99% of all the common replacement parts from all the major brands for all the different appliances, because we want to get your appliance back up and running on our first visit (most Cases.)Rely on us at Appliance Masters for efficient, reliable, affordable appliance repair services. Request an Appliance Repair Appointment today.
Service Call Request
We service the following areas:
Apache Junction Arizona | Chandler Arizona | Gilbert Arizona | Mesa Arizona | Queen Creek Arizona | Scottsdale Arizona | Tempe Arizona | And More…
Frigidaire Appliances | GE Appliances | Kenmore Appliances | Kitchenaid Appliances | LG Appliances | Maytag Appliances | Samsung Appliances | Whirlpool Appliances
Affordable Appliance Repair | Clothes Dryer Repair | Dishwasher Repair | Dryer Repair | Freezer Repair | Fridge Repair | Home Appliance Repair | Ice Maker Repair | Refrigerator Repair | Same Day Appliance Repair | Washer & Dryer Repair | Washer Repair | Washing Machine Repair